SineSet PERMANENT MAGNETIC COMPOUND SINE PLATES by Suburban Tool, Inc.

	Suburban Tool, Inc.

PERMANENT MAGNETIC COMPOUND SINE PLATES

PROUDLY MADE IN OUR FACILITY IN THE U.S.A.

ASK OUR COMPETITION IF THEY CAN SAY THE SAME.

MSPC-66-S1

MSPC-126-FP-S2 Sine Set Permanent Magnetic Compound Sine Plate

MSPC-612-FP-S2

SineSet Permanent Magnetic Compound Sine Plate Drawing

All chucks use ceramic magnets for superior holding power.
Chucks are lubricated and sealed against dirt and liquids.
A removable handle and two rails are included with each chuck.
Two locking straps and two self-storing, hardened & ground rails are included with each SineSet^® compound sine plate.
The gage block roll has two 0.200" minute steps for setting small angles with standard gage block sets.
Models with the suffix "S0, S1 or S2" are part of the SineSet^® System. The chuck can be removed, allowing the individual use of both the compound sine plate and magnetic chuck and allowing other products with the same part number suffix to bolt directly to the compound sine plate (for compatibility chart click here).
The compound sine plate portion is made of steel, hardened to Rc 58-60.

STANDARD POLE: 1/4" poles and 1/8" separators produce deep flux lines for holding large and thick parts.
FINE POLE (marked -FP): 1/8" poles and 1/8" separators produce shallow flux lines for holding small and thin parts.

MODEL	POLE SPACING	SineSet^® SERIES	L	W	H	C1	C2	SQUARE & PARALLEL	WT(#)	PRICE (US$)
SineSet^® COMPATIBLE
MSPC-44-FP-S0	STANDARD	S0	4"	4"	5-3/4"	3" ±0.0002"	3" ±0.0002"	0.0002"	25	$ 2,956
MSPC-66-S1	STANDARD	S1	6"	6"	5-3/4"	5" ±0.0002"	5" ±0.0002"	0.0002"	48	$ 4,295
MSPC-66-FP-S1	FINE	S1	6"	6"	5-3/4"	5" ±0.0002"	5" ±0.0002"	0.0002"	52	$ 4,515
MSPC-612-S2	STANDARD	S2	12"	6"	6-13/16"	10" ±0.0002"	5" ±0.0002"	0.0003"	113	$ 6,261 T
MSPC-612-FP-S2	FINE	S2	12"	6"	6-13/16"	10" ±0.0002"	5" ±0.0002"	0.0003"	118	$ 6,556 T
MSPC-618-S2	STANDARD	S2	18"	6"	8"	15" ±0.0003"	5" ±0.0002"	0.0004"	199	$ 12,199 T
MSPC-618-FP-S2	FINE	S2	18"	6"	8"	15" ±0.0003"	5" ±0.0002"	0.0004"	204	$ 12,587 T
MSPC-812-S2	STANDARD	S2	12"	8"	6-13/16"	10" ±0.0002"	5" ±0.0002"	0.0003"	151	$ 8,468 T
MSPC-812-FP-S2	FINE	S2	12"	8"	6-13/16"	10" ±0.0002"	5" ±0.0002"	0.0003"	156	$ 8,822 T
MSPC-1212-S2	STANDARD	S2	12"	12"	6-13/16"	10" ±0.0002"	10" ±0.0002"	0.0003"	237	$ 12,682 T
MSPC-1212-FP-S2	FINE	S2	12"	12"	6-13/16"	10" ±0.0002"	10" ±0.0002"	0.0003"	243	$ 13,126 T
MSPC-1218-S2	STANDARD	S2	18"	12"	8"	15" ±0.0003"	10" ±0.0003"	0.0004"	408	$ 23,732 T
MSPC-1218-FP-S2	FINE	S2	18"	12"	8"	15" ±0.0003"	10" ±0.0003"	0.0004"	417	$ 24,198 T
NOT SineSet^® COMPATIBLE (CHUCK IS NOT REMOVABLE)
MSPC-66	STANDARD	--	6"	6"	5-3/8"	5" ±0.0002"	5" ±0.0002"	0.0002"	44	$ 4,093
MSPC-66-FP	FINE	--	6"	6"	5-3/8"	5" ±0.0002"	5" ±0.0002"	0.0002"	48	$ 4,265

PRODUCT CERTIFICATIONS

Long Form Certification

A form showing the advertised sizes and/or tolerances.
The actual measurements taken of those sizes and/or tolerances.
A statement that the standards used to measure the tool are traceable to the National Institute of Standards and Technology.

Short Form Certification